international safety standard approvals vde0805/en60950/iec950 file no. 10401-3336-1071 licence no. 90353, 79517 and 1071 ul1950 file no. e136005 csa c22.2 no. 950 file no. lr41062c/lr50913/lr101320 certificate no. 606008 output specifications line regulation single outputs 0.5% ll to hl, fl multi's: +5.1v output 0.5% multi's: aux. outputs 1.0% overshoot/undershoot at turn-on 10% transient response +5.1v 250mv max. dev. (40% to 60% 1ms recovery full load step) to 1% temperature coefficient all outputs 0.025%/c overvoltage protection +5v output only 6.25v 0.75v output power limit primary power limited 45w pin max. short circuit protection continuous with auto restart minimum output current 0a input specifications input voltage range 90 to 264vac 120 to 370vdc input frequency range 47 to 440hz input surge current 110vac 12a max. 230vac 24a max. safety ground 110vac, 60hz 1ma max. leakage current 230vac, 50hz 2ma max. electromagnetic compatibility specifications radiated noise en55022, en55011, fcc level a conducted noise en55022, en55011, fcc level b electrostatic discharge en61000-4-2 level 4 electrostat. air discharge iec801-2 level 3 rf field susceptibility iec801-3 level 3 electrical fast en61000-4-4 level 3 transients/bursts surge susceptibility en61000-4-5 level 3 general specifications hold-up time 110vac 10ms 230vac 60ms efficiency 110vac and 230vac 70% typical isolation voltage input/output 3000vac input/chassis 1500vac switching frequency variable 45khz to 85khz approvals and safety vde0805, en60950 standards babt, iec950, ul1950 csa c22.2 no. 950 case material abs plastic material flammability ul94-5v weight 500g (17.65oz) mtbf mil-hdbk-217e 150,000 hours environmental specifications thermal performance operating 0c to +40c non-operating C40c to +85c 0c to +40c ambient, 25w convection cooled peak (0c to 40c, max. 60s), 35w see note 1 relative humidity non-condensing 5% to 95% rh altitude operating 10,000 feet max. non-operating 30,000 feet max. vibration 5hz to 500hz 2.4g rms (approx.) for new design -ins refer to the scl25 series instead cl25 series single, dual and triple outputs [ 2 year warranty ] ? 90vac to 264vac universal input ? short circuit protected ? vde, ul, csa and babt approved ? vde0871 level b conducted noise ? 25w continuous, 35w peak output power ? stand alone "listed" equipment the cl25 series of 25w (35w peak) external switching power supplies enables the system specifier to optimise the design for several reasons. firstly, because the power supply offers pre-approved selv outputs, the submission of the apparatus for safety approval is simplified. secondly, the task of integrating the power supply into the mechanical design is eliminated, presenting further savings by ensuring a shorter and simpler design cycle. these advantages are complemented by universal input, iec950, ul, csa and babt approvals, to complete a worldwide packaged power solution suitable for a wide variety of low power, desktop applications. specification all specifications are typical at nominal input, full load at 25 c unless otherwise stated page 1 gepr?fte sicherhelt
notes 1 peak output current lasting less than 60 seconds with duty cycle <5%. during peak loading outputs may exceed total regulation limits. 2 50mhz bandwidth, peak-to-peak, measured differentially. 3 total regulation is defined as the static output regulation at 25c, including initial tolerance, line voltage within stated limits and load currents within stated limits. 4 output b of dual models is a floating output. polarity is referenced by user. 5 the output cable length is reduced to 24 for all multiple output models and for the cl25-7605. 6 to maintain user-system safety approvals, the input power cable must be appropriately rated and approved. all dimensions in inches (mm) (160.0 ) + 0.3 - 0.0 (85.0 ) + 0.4 - 0.2 (43.0 ) + 0.2 - 0.0 mini din plug a a .353 dia (8.97) 72.0 ref (1830 30) 6.32 ref 3.35 ref dg j 1 1.71 ref 1 3 2 5 6 4 view a-a scale: none "amp" p/n 750208-4 or equiv. mating part "amp" p/n749232-1 or equiv. 7 8 p1 dl dn j1 mini din plug a a .353 dia (8.97) output output current ripple (2) total model number voltage max peak (1) regulation (3) 5.1v 5.0a 6.0a 100mv 4.0% cl25-7605 (5) 9.5v 2.5a 3.2a 95mv 4.0% cl25-7614 12.0v 2.0a 2.5a 120mv 4.0% cl25-7612 16v 1.5a 2.0a 160mv 4.0% cl25-7616 24.0v 1.0a 1.5a 240mv 4.0% cl25-7624 48.0v 0.5a 0.7a 240mv 4.0% cl25-7617 +5.1v (a) 2.5a 4.0a 50mv 3.0% cl25-7618 12.0v (b) (4) 1.0a 2.0a 120mv 3.0% +5.1v (a) 2.5a 4.0a 50mv 3.0% cl25-7619 (5) 15v (b) (4) 0.8a 1.5a 150mv 3.0% +5.1v (a) 2.5a 4.0a 50mv 3.0% cl25 -7620 (5) 24v (b) (4) 0.5a 1.0a 240mv 3.0% +5.1v (a) 2.0a 4.0a 50mv 4.0% cl25-7608 (5) +12v (b) 1.0a 2.0a 120mv 5.0% C 12v (c) 0.2a 1.0a 120mv 5.0% +5.1v (a) 2.0a 4.0a 50mv 4.0% cl25-7610 (5) +15v (b) 0.5a 1.5a 150mv 5.0% C15v(c) 0.2a 1.0a 150mv 5.0% pin single dual triple number output output output pin 1 v a v a v a pin 2 v a v a v a pin 3 v a v a v a pin 4 v a v b +v b pin 5 return v b Cv c pin 6 return return return pin 7 return return return pin 8 return return return 25 watt ac/dc external power supplies ac/dc power supplies | 25w ac/dc page 2 http://www.artesyn.com ds_cl25_19980401.pdf
|
